Contractor School Online ®
The premiere national online resource to assist you in passing your Contractor License Exam.

Tell a friend!

Email or Call (800)966-9596
Home  |  National Contractor License  |  Request Information  |  Construction Glossary  |  Login

Colorado-Roofing Online Practice Test

These are actual questions from our online practice test.

We have included a question from each chapter of the test. Every question will be multiple choice. The answers are not included with the sample.

Sample Questions

# Chapter Title Question
1 Roofing, Shakes, Flashing, Shingles, Tar, Roof Coverings, Galvanized and Steel Corrugated steel can be placed over ___________.
2 Roofing, Composition Shingles, Metal Roofing, Drainage Slope and Asphalt

The slope to drain towards downspots should be at least _________ inch per linar foot of gutter run.

3 Roofing, Eaves, Gables, Asphalt Shingles, Rafters and Membrane

What is the distance called fron the lower edge of a top shingle to the upper edge of the shingle in the course below it?

4 Roofing, Aluminum, Roofing Panels, Galvalume, Galfan, Hips, Valleys and Seams What type of metal used for roofs is even more durable than aluminum?
5 Framing and Roofing Regarding soffit, install receiving channels (soffit receiver or J-channel). Nailing strips must be installed if the eave span is greater than ______ (406mm), unless otherwise specified in the soffit manufacturer's instructions. In areas with high wind restrictions, nailing should not exceed 12" (305mm) on center, unless otherwise specified by the manufacturer.
6 Steel Framing

 A _____________  is one of the horizontal supporting members that run between foundations, walls, or beams to support a ceiling or floor. They may be made of woodengineered woodsteel, or concrete. Typically it has the cross section of a plank, while a beam is bigger than a joist. Joists are often supported by beams laid out in repetitive patterns.

7 Joists and Exposed Beams One of the horizontal supporting members that run from wall to wall, wall to beam, or beam to beam to support a ceiling, roof, or floor is referred to as a ______________________.
8 Joists and Girders

HOW MANY JOISTS SPACED 16" ON CENTER ARE REQUIRED FOR A BUILDING 120' LONG?

9 Tile Roofing

Roof tiles are designed mainly to keep out _____________, and are traditionally made from locally available materials such as terracotta or slate. Modern materials such as concrete and plastic are also used and some clay tiles have a waterproof glaze

10 Slate Roofing

Synthetic slate is engineered to last longer than authentic slate (at least 40 to ____________ years). It’s also low maintenance, stands up to harsh weather and is highly fire resistant. Green homeowners appreciate the sustainable design of composite slate. Made from recycled products, the tiles are also fully recyclable when it’s time to replace damaged pieces—or install an entirely new roof!

11 Metal Roofing, Flashing and Installation What is sometimes called cane metal that is made from a solid sheet in which a regular pattern of holes has been punched?
12 Rain Gutters, Downspout Installation and Duct Work Installation What are objects called that are the same on both sides of the centerline?
13 Thermal and Moisture Protection Which material has the best moisture protection?
14 Elastomeric Roofing

What precedures are necessary to prepare the roof for the Coating process?

15 Rules of Construction, General Safety, Health Provisions and Fire Extinguishers On a jobsite, you have to have a fire extinguisher for safety purpose within:
16 Asbestos, Code of Federal Regulations Title 29, Part 1926, Safety and Training As part of the safety training process, contractors' supervisors are required to conduct "toolbox" and "tailgate" safety meeting. How often must these be held?
17 Basic Bid Preparation and Estimating The notice to owner contained in a contract, informs the customer of _________________.
18 Mathematics, Calculations and Formulas

In a square all the sides are equal in length and all the angles are equal to 90 degree. The diagonals of a square are equal to each other.

Square



Go Back
What We Offer  |  Obtaining a Trade License  |  Test Preparation  |  About Us  |  Contact Us

Copyright © 1998-2019, Contractor School Online®,All Rights Reserved